Hi all,
Im glad to find a local group to join
I have a vindicator sprint rolling chassis and just put a rx8 6 speed box coupled to a st170 engine.
I am attempting to set it up on standard ecu inlet ect and wondering if there is anyone local that can assist with wiring?
Newbie saying hi looking for tech assistance and soon to be run out companions
Moderator: Contaminated
- steve m
- Posts: 2891
- Joined: Mon May 09, 2011 9:01 pm
- Location: Crawley West sussex
- Contact:
Re: Newbie saying hi looking for tech assistance and soon to be run out companions
Welcome to the club
In the for sale area, we have a member who makes wiring kits, he may be able to assist
viewtopic.php?f=4&t=8345
good luck, and hope to see you out soon
regards
steve
In the for sale area, we have a member who makes wiring kits, he may be able to assist
viewtopic.php?f=4&t=8345
good luck, and hope to see you out soon
regards
steve
Thats was probably spelt wrong, or had some grammer, that the "grammer police have to have a moan at
- Nash
- Posts: 9877
- Joined: Thu Mar 04, 2010 9:12 pm
- Location: near Ashford, Kent
- Contact:
Re: Newbie saying hi looking for tech assistance and soon to be run out companions
Hi Tobe and welcome to the club. I see you are in Barming. I'm not your man for wiring up ecu's but I'm sure someone will be along in a while who is.
If there is anything else you need that I can help with then Barming isn't far in real terms to me.
Once again welcome.
....... Neil
If there is anything else you need that I can help with then Barming isn't far in real terms to me.
Once again welcome.
....... Neil
Buckle Up - Adventure Calls
Re: Newbie saying hi looking for tech assistance and soon to be run out companions
[quote="steve m"]Welcome to the club
In the for sale area, we have a member who makes wiring kits, he may be able to assist
Thanks Steve, just messaged martin appreciate your assistance
In the for sale area, we have a member who makes wiring kits, he may be able to assist
Thanks Steve, just messaged martin appreciate your assistance
Re: Newbie saying hi looking for tech assistance and soon to be run out companions
[quote="Nash"]Hi Tobe and welcome to the club. I see you are in Barming. I'm not your man for wiring up ecu's but I'm sure someone will be along in a while who is.
Thanks Nash, appreciated
Here's the mess
Thanks Nash, appreciated
Here's the mess
-
- Site Admin
- Posts: 10185
- Joined: Thu Dec 03, 2009 10:34 am
- Contact:
Re: Newbie saying hi looking for tech assistance and soon to be run out companions
welcome onboard, well i def cant help with wiring - unless you want a bigger mess! but hope that you can get it sorted , worst ways if the diy route doenst work, you could always give Dick/Jay a call at Snodhurst garage which isnt far from you - they love a kit car challenge
cheers
Mark
cheers
Mark
- Tony T
- Posts: 559
- Joined: Tue Feb 07, 2012 2:18 pm
- Contact:
Re: Newbie saying hi looking for tech assistance and soon to be run out companions
Welcome mate eerr the wheels are should be pointing down And the banter starts
Tony T
Tony T
- DJ.
- Posts: 6000
- Joined: Mon May 30, 2011 7:31 pm
- Contact:
Re: Newbie saying hi looking for tech assistance and soon to be run out companions
Hi and welcome to SKCC
I'm no wiring expert either, but hope to see you put on a run soon.
I'm no wiring expert either, but hope to see you put on a run soon.
- Tony B
- Site Admin
- Posts: 6333
- Joined: Sat Feb 20, 2010 1:57 pm
- Location: Maresfield, East Sussex
- Contact:
Re: Newbie saying hi looking for tech assistance and soon to be run out companions
Did someone mention wiring???
Welcome to the club, why not try to blag a passanger seat on one of our upcoming sunday morning outings?
Welcome to the club, why not try to blag a passanger seat on one of our upcoming sunday morning outings?
- b33fy
- Posts: 6325
- Joined: Sat Mar 31, 2012 11:40 am
- Location: Tonbridge
- Contact:
Re: Newbie saying hi looking for tech assistance and soon to be run out companions
Welcome, oem ecu's are a pain to wire in with built in immobiliser circuits, etc. I believe it was retro ford magazine or similar who did a two part article a while ago on wiring in a black top using the oem ecu. I've had a quick scan but can't see it online. may be worth checking out some of the retro car type sites as there may be a tech guide knocking about somewhere.
All the best with it, hope it doesn't give you too much of a headache.
All the best with it, hope it doesn't give you too much of a headache.
Power.. small nail, fast hammer, Torque.. small nail, big hammer.. I got a big hammer
Return to “New Members - Say Hello Please”
Who is online
Users browsing this forum: No registered users and 9 guests