Page 1 of 2
Newbie saying hi looking for tech assistance and soon to be run out companions
Posted: Tue May 17, 2016 10:52 pm
by tobeleigh
Hi all,
Im glad to find a local group to join
I have a vindicator sprint rolling chassis and just put a rx8 6 speed box coupled to a st170 engine.
I am attempting to set it up on standard ecu inlet ect and wondering if there is anyone local that can assist with wiring?
Re: Newbie saying hi looking for tech assistance and soon to be run out companions
Posted: Wed May 18, 2016 3:40 am
by steve m
Welcome to the club
In the for sale area, we have a member who makes wiring kits, he may be able to assist
viewtopic.php?f=4&t=8345good luck, and hope to see you out soon
regards
steve
Re: Newbie saying hi looking for tech assistance and soon to be run out companions
Posted: Wed May 18, 2016 5:26 am
by Nash
Hi Tobe and welcome to the club. I see you are in Barming. I'm not your man for wiring up ecu's but I'm sure someone will be along in a while who is.
If there is anything else you need that I can help with then Barming isn't far in real terms to me.
Once again welcome.
....... Neil
Re: Newbie saying hi looking for tech assistance and soon to be run out companions
Posted: Wed May 18, 2016 8:52 am
by tobeleigh
[quote="steve m"]Welcome to the club
In the for sale area, we have a member who makes wiring kits, he may be able to assist
Thanks Steve, just messaged martin appreciate your assistance
Re: Newbie saying hi looking for tech assistance and soon to be run out companions
Posted: Wed May 18, 2016 8:54 am
by tobeleigh
[quote="Nash"]Hi Tobe and welcome to the club. I see you are in Barming. I'm not your man for wiring up ecu's but I'm sure someone will be along in a while who is.
Thanks Nash, appreciated
Here's the mess
Re: Newbie saying hi looking for tech assistance and soon to be run out companions
Posted: Wed May 18, 2016 9:54 am
by greenwoo
welcome onboard, well i def cant help with wiring - unless you want a bigger mess! but hope that you can get it sorted , worst ways if the diy route doenst work, you could always give Dick/Jay a call at Snodhurst garage which isnt far from you - they love a kit car challenge
cheers
Mark
Re: Newbie saying hi looking for tech assistance and soon to be run out companions
Posted: Wed May 18, 2016 3:43 pm
by Tony T
Welcome mate eerr the wheels are should be pointing down
And the banter starts
Tony T
Re: Newbie saying hi looking for tech assistance and soon to be run out companions
Posted: Wed May 18, 2016 4:44 pm
by DJ.
Hi and welcome to SKCC
I'm no wiring expert either, but hope to see you put on a run soon.
Re: Newbie saying hi looking for tech assistance and soon to be run out companions
Posted: Wed May 18, 2016 5:42 pm
by Tony B
Did someone mention wiring???
Welcome to the club, why not try to blag a passanger seat on one of our upcoming sunday morning outings?
Re: Newbie saying hi looking for tech assistance and soon to be run out companions
Posted: Wed May 18, 2016 6:05 pm
by b33fy
Welcome, oem ecu's are a pain to wire in with built in immobiliser circuits, etc. I believe it was retro ford magazine or similar who did a two part article a while ago on wiring in a black top using the oem ecu. I've had a quick scan but can't see it online. may be worth checking out some of the retro car type sites as there may be a tech guide knocking about somewhere.
All the best with it, hope it doesn't give you too much of a headache.