Having done a compression test on the race engine a while back I knew that 2 cylinders were down on compression, so I decided to take the head off another engine and refresh it then fit it to the engine in the car.
When I took the head off the old engine on the floor I found it had valves that didn’t seal and a broken valve spring. So once I’d cleaned and had the head skimmed I then rebuilt it with all the valves ground in nicely to give a good seal.
Today I decided to get on with the head swap and when I took the cam off found that all the lobes were badly worn.
I put petrol on top of the pistons while I cleaned the block up and nothing disappeared so the rings must be fairly good and you can still see the cross hatching on the bores.
So I have fitted the cam from the old engine ( which looks good ) and have now nearly finished putting it all back together. Hopefully I’ll get it finished and running again tomorrow
Minirod engine
Moderator: Contaminated
- nelmo
- Posts: 514
- Joined: Sat Aug 29, 2015 1:25 pm
- Location: Reigate, Surrey
- Contact:
Re: Minirod engine
Yeah, I managed to mow the lawn... almost as impressive, I think? ![Neutral :|](./images/smilies/icon_neutral.gif)
![Neutral :|](./images/smilies/icon_neutral.gif)
My build blog: http://zerolifebuild.blogspot.co.uk
-
- Posts: 1353
- Joined: Sun Aug 12, 2012 7:41 pm
- Contact:
Re: Minirod engine
Worn and PITTED !!!!!! mind you Matt the pitts would have distributed oil?
One is one too many and one too many is never enough.
- DJ.
- Posts: 6001
- Joined: Mon May 30, 2011 7:31 pm
- Contact:
Re: Minirod engine
I'm hoping this gives you the edge at the last meeting ![Cool 8-)](./images/smilies/icon_cool.gif)
![Cool 8-)](./images/smilies/icon_cool.gif)
- Matth93
- Posts: 2403
- Joined: Thu Nov 08, 2012 10:43 pm
- Contact:
Re: Minirod engine
I hope this helps for the last meeting. Then my plan is to actually build a engine for next year instead of running a 100,000 mile engine and hoping it holds together
Then with a bit of luck I’ll have a better chance at winning next year.
![Laughing :lol:](./images/smilies/icon_lol.gif)
- Jasonmpk
- Posts: 238
- Joined: Thu Jun 11, 2020 3:50 pm
- Contact:
Re: Minirod engine
Well done Matt, let me know if you need any help as I've been out working this morning but I can help this afternoon and tomorrow if needed?
Jason
Jason
- Matth93
- Posts: 2403
- Joined: Thu Nov 08, 2012 10:43 pm
- Contact:
Re: Minirod engine
Thanks for the offer Jason, it’s all done now.
Finished putting it all back together and cranked it over without the plugs in first to get the oil round it. It fired up straight away and sounds nice, I ran it up for a while then took the plugs out and done a compression check on it and found all the cylinders now have almost the same 15bar on every one. So pleased with that all cylinders have gone up too. Now it’s just waiting for race day to test it
Finished putting it all back together and cranked it over without the plugs in first to get the oil round it. It fired up straight away and sounds nice, I ran it up for a while then took the plugs out and done a compression check on it and found all the cylinders now have almost the same 15bar on every one. So pleased with that all cylinders have gone up too. Now it’s just waiting for race day to test it
- Wingco
- Posts: 2761
- Joined: Thu Jul 26, 2012 9:49 am
- Location: Swanley, Kent
- Contact:
Re: Minirod engine
With that rebuilt engine your smash it Matt and I don't mean crash it
![Very Happy :D](./images/smilies/icon_e_biggrin.gif)
![Very Happy :D](./images/smilies/icon_e_biggrin.gif)
![Very Happy :D](./images/smilies/icon_e_biggrin.gif)
Mirror, Signal go faster pedal !!
- Jasonmpk
- Posts: 238
- Joined: Thu Jun 11, 2020 3:50 pm
- Contact:
Re: Minirod engine
Matth93 wrote:Thanks for the offer Jason, it’s all done now.
Finished putting it all back together and cranked it over without the plugs in first to get the oil round it. It fired up straight away and sounds nice, I ran it up for a while then took the plugs out and done a compression check on it and found all the cylinders now have almost the same 15bar on every one. So pleased with that all cylinders have gone up too. Now it’s just waiting for race day to test it
Just a thought Matt, do you have any trade plates that could let you test it before on the roads, or maybe put the plates back on for a road test ?
- Matth93
- Posts: 2403
- Joined: Thu Nov 08, 2012 10:43 pm
- Contact:
Re: Minirod engine
I have got the number plates for it but the mot etc has all run out now and it stands out a bit too much to risk it without. I might see if I can get a sneaky lap or two in next Saturday as I’m taking the car to Lydden to put it on the clubs stand at the rallycross meeting
Return to “Car Related Discussion”
Who is online
Users browsing this forum: No registered users and 56 guests